Certified technicians, professional drying equipment and moisture readings you can see for yourself. No guesswork.
You get a straight answer on cost up front, with every line explained and nothing hidden.
Filing a claim is easier with good records. We document everything and talk to your adjuster for you.
Most people who call us have never dealt with attic water damage before. We walk you through it on the phone, then send a local crew with the right equipment.
Water reaches an attic from two directions. From above, rain enters through failed flashing, worn shingles, or the seals at chimneys and vents. The house itself sends moisture upward too, and in a poorly ventilated attic it condenses on cold sheathing. Either way, hardly anyone goes up there to look. Our team in Carmel inspects the attic, finds the source, and dries it out.
On the typical attic job, soaked insulation is the main issue. Heating and cooling bills go up because cellulose and fiberglass alike give up R-value when wet. Worse, soaked insulation holds water against the ceiling drywall and the framing for weeks. We remove what is saturated, dry the wood with air movers and dehumidifiers, and treat any mold on the rafters or sheathing.
We check the roof deck, flashing points, vents and exhaust ducts to learn whether the water is a leak, condensation, or both. How far it spread is shown by moisture meters and thermal imaging.
Saturated or moldy insulation is bagged and removed so the wood and drywall under it can dry. Rooms under the attic are protected, and the route in and out stays contained.
Rafters, sheathing and joists are dried by air movers and dehumidifiers until their moisture levels are normal. Visible mold is cleaned from the wood and an antimicrobial is applied.
We point out the roof or ventilation problem that needs correcting and can share our findings with your roofer. New insulation is installed to bring back the R-value after the attic is staying dry.
Rain that gets past the roof lands in the insulation, which absorbs it. With no sign inside the house, nobody notices the leak and the roof stays unrepaired.
Damp wood and paper facing in a warm, still attic are ideal for mold. Growth can begin on the sheathing and on the back of the ceiling drywall.
Once storm after storm has saturated the insulation, the ceiling starts getting wet. Brown rings appear in the room below, and the drywall may start to sag.
The sheathing comes apart in layers and no longer grips the roofing nails. Mold spreads across large sections of the roof deck, and the rafters remain damp enough to decay.
Air handlers, with their drain pans and condensate lines, sit in many attics. A clogged drain or an overflowing pan drips into the insulation for weeks, with no storm to warn you.
Compressed, damp insulation does very little insulating, and it may not recover after it dries. Energy bills climb, and the rooms below the wet area are hotter or colder than the rest.
With poor ventilation, mold commonly grows on the bottom of the roof deck. It can cover a wide area before anyone goes up to look.
An attic contains recessed light cans, junction boxes and runs of cable. Do not enter the attic before someone checks the power, because wet electrical parts can shock you or start a fire.
It depends on the material, how long it stayed wet and how clean the water was. We test before we decide, and we tell you why.
Call (612) 464-8280| Material | Can usually be saved when | Has to be replaced when |
|---|---|---|
| Cellulose insulation | Only the surface is damp and it is still loose | In most cases, because it has packed down or soaked through |
| Fiberglass insulation | Quick drying of a small area that took clean rainwater | Any mold, dirt or matting, or wetness lasting past a few days |
| Roof sheathing | Stained but solid, and it dries back to normal moisture readings | Soft, sagging between rafters, or its layers are separating |
| Ceiling drywall | A dry, flat stain that can be sealed and repainted | Weeks beneath saturated insulation, or any sagging or crumbling |
| Rafters and joists | Surface staining or light mold on wood that is still sound | Visible cracks, or rot soft enough for a screwdriver to sink in |
Have a different question? Call us and we will answer it over the phone.
Call (612) 464-8280Don't wait for small problems to become expensive emergencies. Call Carmel Restoration for fast, reliable service.
Call (612) 464-8280 Now